Operator manual for bench vise with swivel base

It is important that your read the entire bench manual supplied by the bench vise manufacturers or bench vise suppliers to become familiar with the bench vise with swivel base.

Before uses of bench vise with swivel base Make sure the bench vise is securely mounted before using,and Please check for if have any damaged parts on the bench vise.

the bench vise with swivel base comes completely assembled.  Before proceeding the bench vise, wipe down the swivel bench vise with a degreasing solution or dish soap and water to remove any packaging grease on your bench vise.

Swivel bench vise mounting options:

Your swivel bench vise comes with mounting holes on the Base Foot.  Use the appropriate hardware to secure the swivel bench vise to your workbench. 

Before assembling your bench vise with swivel base, be sure that you have all parts described in the bench vise parts list supplied by bench vise manufacturers or suppliers in packing carton

Assemble attachments based on the intended use of the tool.

Mounting the swivel bench vise to a Wooden Workbench:

1.Measure the thickness of your workbench. To securely mount swivel bench vise to a wooden workbench, mount a wood washer underneath the mounting points for the bench vise in order to add strength.

2.Purchase three or four bench vise mounting bolts, nuts, and flat washers the appropriate length of your workbench and add one inch of length to the bolts to make up for the extra inch of the bench vise

3.Mark and drill the holes through the workbench, using the base as a template, for the mounting tabs on the base of the swivel bench vise.

4.Position the vise on the workbench and line up the holes drilled in step 3 with the holes in the mounting tabs.

5.Insert the Bolts into the mounting tabs and through the workbench.

Mounting the swivel bench vise to a metal Workbench:

1.Measure the thickness of your workbench. To securely mount your swivel bench vise to a metal workbench, mount an thick reinforcing plate underneath the mounting points when step 6 is performed.

2.Purchase three or four bench vise mounting bolts, nuts and flat washers that are the appropriate length for the thickness of the workbench. and add one inch of length to the bolts to make up for the extra inch of the bench vise.

3.Mark and drill the holes through the workbench, using the base as a template, for the mounting tabs on the base of the swivel bench vise.

4.Mark and drill the reinforcing plate, using the base of the bench vise as a template.

5. Position the vise on the workbench and line up the holes drilled in step 3 with the holes in the mounting tabs.

6.Insert bolts into the mounting tabs, and through the workbench (Remember to attach the reinforcing plate underneath the workbench, then thread on the nuts and tighten the bolts)

Clamping:

1.Open the bench vise with swivel base by turning the handle counterclockwise, until you have l/4" of space between your material and each jaw of the bench vise.

2.Hold the material between the jaws while you slowly tighten the bench vise by turning the handle clockwise. When your materials snug between the jaws, stop tightening.

3.Tighten the bench vise until you can no longer move the material you are working on.  do not over-tightening.

4.When finished working on the material, turn the handle counterclockwise. This will release the material from the bench vise.

Swivel base:

When the material is securely clamped in the bench vise, decide if you need to rotate the bench vise to allow better and safer access to material while working.  lf you need to change the position of the swivel bench vise, please follow the steps below.

1.Locate the Locking Clamps one to each side of the bench vise with swivel base.

2.Unlock each Locking Clamp lever by turning it counterclockwise.

3.Swivel the vise until you have better and safer access to your material

4.Lock each Locking Clamp lever by turning it clockwise until tight.

workbench with swivel bench vise

workbench with swivel bench vise

 

 

 

 

 

 

 

 

 

 

 

Related Reading

china bench vises manufacturers face tough competition around the worlds

Heavy Duty Bench Vises

American Type Bench Vises

Multi-Purpose Bench Vises

GS TUV VPA Approved Bench Vises

England Type Vises

Light Duty Bench Vises

Japan Type Bench Vises

Steel Bench Vises

Table Vises

Other Vises

the key to bench vise mounting

原创文章,转载请注明: 转载自DLFT CO.,LTD

本文链接地址: Operator manual for bench vise with swivel base

#entry-meta
#post-1230-->

the key to bench vise mounting

Bench Vise mounting can be mounted in variety of positions and on many different styles of bench vise mounting options. The key to successful installation is careful planning and preparation. Installed properly, the bench vise will give a lifetime of daily service from the time you get the bench vises from bench vises suppliers. that is the best bench vise mounting ideas.

Bench vise mounting depending on the bench's top thickness, you have two mounting options. If your top is at least 2" thick, lag screws work fine. With washers attached.

Tun the lags up from underneath the bench vise's carriage, through the spacer block and into the underside of the bench top. If your top is less than 2" thick, install carriage bolts right through the bench top and secure them with nuts and washers under the bench vise's carriage. Be sure to countersink the heads of the bolts below the surface of the top to prevent tool or work damage.

Plug or fill the holes by any method that pleases you. With either mounting technique, you'll want to occasionally check the hardware to be sure it isn't working loose. As for maintenance bench vises or lubricate the threads of the main screw of bench vise with light oil and wax the guide rods occasionally.

Place the bench vise mounting bolts down through the vise base holes and through the bench. Screw on the nuts and tighten them with the proper sized wrench. Untighten and remove the C-clamp and you can start bench vise mounting.

1. remove the four bench vise mounting bolts and nuts from the four corners in the base of the vise. Position the vise onto the location you want it on the mounting bench.

If you're right handed, typical mounting positions would be either toward the left of the front edge of the bench, or the right end of bench. Carvers will probably find the end position most useful, as will those who clamp wide, flat work like doors and large panels. For general purpose work, the bench's front edge is probably the best option. Just be sure the bench vise doesn't interfere with the bench's legs or aprons.

Also, take into account that the bench vise will have wooden jaw liners,that stick out past the edge of the bench vise. Most people prefer have the ends of the jaw liners flush with a corner of the bench top, so take that into consideration when you locate bench vise.

2,clamp bench vise down to the bench by setting the top of the C-clamp onto the base of bench vise and the bottom of the C-clamp under the table or the bench you are attaching bench vise to. Tighten the clamp so that the bench vise will stay in the place you want it.

For most bench tops, you'll need to mount a spacer between bench vise carriage and the underside of the bench top. You'll want Bench vise's cast iron jaws set about 1/2" below the top surface of the bench to protect your tools from accidental contact. measure the distance between bench vise carriage and the underside of the bench. This distance is the thickness of your spacer. We recommend building the spacer from all of which are relatively crush-resistant.

3.Find the drill bit that is the same size as the bolts that were in the base of bench vise. Tighten the proper sized drill bit into the drill. Drill out all four holes through the bench vise base holes and through the bench you are amounting the bench vise onto.

4.Once you've determined the thickness of the spacer block, you'll need to mortise the rear jaw into the edge of your bench top. Put the bench top on edge and secure it well. Temporarily clamp the vise with the spacer blocks to the bench top. The depth of the mortise will be the thickness of the rear jaw. On some vise models, you may also have to remove additional material to accommodate any reinforcement webbing cast into the bench vise's carriage.

5.Wooden liners expand your vise's holding capacity and prevent your work from being marred by the cast iron jaws. Any hardwood will work as a liner material. The front jaw liner should be at least 1 5/8" thick to prevent deflection and so you can drill holes in the top of the liner for bench dogs if you like.

6.The rear jaw only needs to be 3/4 – 1" thick because it will be supported by the edge of the bench. For small vises like the Anant 52 and the Groz 7", make the liner length 12 – 14". Anything longer will cause excessive racking and shorten the life of your vice.

7.In the end of bench vise mounting,the jaw liners need to be at least 1/8" above the bench vise's guide posts to allow for seasonal movement and flush with the top of the bench. However you choose to attach your jaw liners to the bench vise, make bench vises can be easily removed if they become damaged or warped. At this point, close the bench vise and make sure the liners mate up acceptably and shim if necessary. Remember, the jaws of bench vises toe in where they meet at the top and should do so after the liners are installed.

bench vise mounting picture

bench vise mounting picture

 

 

 

 

 

 

 

 

 

 

 

Related Readings

china bench vises manufacturers face tough competition around the worlds

American Type Bench Vises

Heavy Duty Bench Vises

Light Duty Bench Vises

Multi-Purpose Bench Vises

GS TUV VPA Approved Bench Vises

England Type Vises

Japan Type Bench Vises

Steel Bench Vises

Table Vises

Other Vises

 

 

原创文章,转载请注明: 转载自DLFT CO.,LTD

本文链接地址: the key to bench vise mounting

#entry-meta
#post-1156-->

china bench vises manufacturers face tough competition around the worlds.

China bench vises manufacturers face tough competition around the worlds.

As we know bench vise made in china keep export to USA for many years and have lot of sales.

but recently. China bench vises manufacturers have to face much more tough situation and very hard compeition from those bench vise manufactuers from the worlds. 

such as:bench vise manufacturers india,bench vices suppliers south africa,bench vice suppliers in bangalore,bench vises suppliers in pune,bench vices suppliers-chennai,bench vise suppliers in uae,bench vises suppliers in hyderabad,bench vice supplier in mumbai,etc. 

all these bench vises suppliers' quality is not as good as bench vise made in china. but because those country's bench vises manufacturers have lower salary cost, lower currency change rate against US dollar, all these make china bench vises suppliers in very tough condition.

especially bench vise manufacturers in india. they have almost as same  foundrymanship as china. as same quality bench vices, but they have lower worker cost, lower currency change rate. that make china bench vises manufacturers in a very tough condition. 

but one things that china bench vises suppliers advance have. that is our transport highway can make sure delivery on time. this is our advantage.another is our quality is better than others suppliers.

so from now on, China bench vise manufacturers and suppliers. must enhance our quality control. improve managing system. so that to lower production cost,and enhance QC controle. to make sure quality best, delivery on time. so that to keep china bench vises keep lots of exporting to USA.Europe and Japan market.

bench vises made in china

bench vises made in china

 

 

 

 

 

 

 

 

 

 

Related Readings

American Type Bench Vises

Heavy Duty Bench Vises

Light Duty Bench Vises

Multi-Purpose Bench Vises

GS TUV VPA Approved Bench Vises

England Type Vises

Japan Type Bench Vises

Steel Bench Vises

Table Vises

Other Vises

the key to bench vise mounting

原创文章,转载请注明: 转载自DLFT CO.,LTD

本文链接地址: china bench vises manufacturers face tough competition around the worlds.

#entry-meta
#post-1130-->